|
Post by ajsuk on Dec 27, 2004 16:11:33 GMT -5
I would imagine Hi would be the positive High beem input, Low would be the positive Low beem input, and the Com would be the earth for both circuits, as they both come out of the same terminal.
|
|
Oggs
loves it here
Choo Choo
Posts: 134
|
Post by Oggs on Dec 27, 2004 16:18:36 GMT -5
ok i just had a look at my angel eye and it goes like this;
Blue is Hi Red is Low Black is Com as its connected to both lights.
just need the H7 wiring pattern now....
|
|
|
Post by ajsuk on Dec 27, 2004 16:36:16 GMT -5
That will be more tricky to find, as the H4 connector is simply the same layout as the H4 bulb, as the wires go straight fromt he connector to the terminals, so the diagram you may have found could just simply be that of the bulb terminals, which is fine, however the H7 Pug connector is more specific, as they arent just the same as the H7 bulb connectors, which just have 2 terminals each, and the wires join up to the connector differently. I hope this makes sense, basically what Im saying is that the Pug H4 connector layout is the same as an H4 bulb, so finding the wiring pattern is easy, but the Pug H7 connector wiring layout isnt the same as an H7 Bulb, as it contains connections for both high beam and low beam (2 H7 Bulbs) Hope Im making this clear
|
|
Oggs
loves it here
Choo Choo
Posts: 134
|
Post by Oggs on Dec 27, 2004 16:42:13 GMT -5
ok i understand what you are saying.....which basically equates into i have little chance of finding out the pattern?
|
|
|
Post by ajsuk on Dec 27, 2004 16:44:27 GMT -5
Im just looking at the instructions I have for my Angels. Do you have the Ultra angel eye lights? If so you may have the same sheet of instructions. It seems to show that if you have H7 wiring, as you do, then you simply cut out the H4 wiring in the Angels, and use your H7 wiring from your current lights instead, including the bulb holders and everything, its a direct swap. It shows this in the bottom right diagram box on the first side of the instrucitons. Also I had another bit of paper, which says that the Black wire from the halo ring connects to the negative sidlight wire.
|
|
Oggs
loves it here
Choo Choo
Posts: 134
|
Post by Oggs on Dec 27, 2004 16:49:06 GMT -5
yes i do have the ULRTA angel eyes and i see the image shows H4 wiring being circled and some scissors suggesting to cut of the wires. but if i cut off the H4 wires how will i connect the current H7 wires?
I had only one peice of paper with mine, nothing about the LED.
|
|
|
Post by M3RAN on Dec 27, 2004 16:50:07 GMT -5
i say instead of splicing your wires on the sidelights to connect the halo wire your these... or then its easier to remove the when needed and add other lighting connections to them too simply place the wire you wish to connect on the join and place in the line of the cable you feeding from and close the top
|
|
|
Post by ajsuk on Dec 27, 2004 16:52:16 GMT -5
It doesnt show how youd go about putting in the new H7 wiring, have a look at your H7 wiring with the bulb terminals on your current headlights, even take the whole thing out (as it shows in the 2 boxes before the one we are talking about) and see if it fits no problem into your angels. If so, you may just have to cut out the H4 wiring from the angels, put in the H7, feed it through a hole in the rubber seal on the back of the angels, and plug any hole in the seal around the wire with sealent or something?
|
|
Oggs
loves it here
Choo Choo
Posts: 134
|
Post by Oggs on Dec 27, 2004 16:58:13 GMT -5
ok so you think i can just take the connectors straight off my standard headlights and plug them directly onto the angels and completely remove the H4 from the scene, now that would be alot easier so the chances of that being the case are pretty remote!
|
|
|
Post by ajsuk on Dec 27, 2004 17:03:24 GMT -5
Well judging by the instructions (which arent clear I know!) thats what it seems to suggest you do! So it might well be possible. The first box says to take off all the bits on your car to get the current lights off, the next 3 show "H7" 206 light setup and how to remove the wiring from your current headlight, the next one shows to use your H7 wiring instead of the angel eye H4 wiring, on the next page it shows H4 setup so we can ignore that, but I dont quite understand what its trying to show with the two H7 boxes in the middle of the page there, its the Pug light, not the angel one, and it seems to show putting the wiring back in the Pug light! Dont knwo why...
Theres definatly no harm in taking out the H7 wiring from your current headlights and seeing if they fit without problem into your angels, I think it could work!
Also, if they are showing how to remove your H7 wiring from your current headlight in the instructions, I'd imagine that they expect you to use them. Whoever drew up these diagrams should be smashed on the head with a bat
|
|
|
Post by M3RAN on Dec 27, 2004 17:08:01 GMT -5
would be pass through the rubber seal? be water aswell then!
|
|
Oggs
loves it here
Choo Choo
Posts: 134
|
Post by Oggs on Dec 27, 2004 17:08:24 GMT -5
yes the instructions are crap espicially when you havent got a clue what h7, h4, etc means but know i understand it a bit so it makes a bit more sense. so tomorrows job is to whip out the light and see if the connector will fit my angel....fingers crossed! thanks for your help!!!!!!!!
|
|
|
Post by ajsuk on Dec 27, 2004 17:13:36 GMT -5
Not a problem! You could, in theory, if you were replacing the wiring in the angels with your H7, cut the H7 wires off of the H7 connector, and feed the 3 wires through the 3 holes in the seal that the H4 wiring currently run through, and then re-solder them back onto the connector once through the seal, this way you avoid cutting the seal and having to patch any holes up.
|
|
Oggs
loves it here
Choo Choo
Posts: 134
|
Post by Oggs on Dec 28, 2004 9:25:06 GMT -5
well job done all fitted and working!! the whole job took about 2hours but if i had known how to get the standard lights out and remove the grill and all that it, could have been done in about 1 hour. Anyway they work and i have wired the LED too which works but its not that bright but i'll need to wait untill dark to test it properly. I have pictures on my pc but i dont how i get them on here for you to look at.... ??
|
|
|
Post by M3RAN on Dec 28, 2004 10:01:27 GMT -5
|
|